This article mainly introduces:

Austria hydraulic cylinder,stainless steel cylinder manufacturer,stainless steel cylinder

(Austria stainless steel cylinder,produced by Hengyu Hydraulic Cylinder Factory）

stainless steel cylinder are widely used in Austria，because of no need for deceleration device，long service life，smooth movement.So our company has designed stainless steel cylinder for customers from Austria.

Introduction to stainless steel cylinder:

Factors that should be considered when selecting the oil seal in the stainless steel cylinder: some specific factors should be taken into account when selecting the oil seal in the stainless steel cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: stainless steel cylinder diameter, piston rod diameter, piston rod and piston groove size, stainless steel cylinder working pressure, stainless steel cylinder movement speed, hydraulic system oil temperature and stainless steel cylinder working environment.

When installing the stainless steel cylinder pipe, the pipe should be cleaned after installation, and should not pass through the stainless steel cylinder block, and the by-pass pipe must be installed in front of the oil port of the stainless steel cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the stainless steel cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the stainless steel cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

stainless steel cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

The assembly work of the stainless steel cylinder has a great impact on the quality of the stainless steel cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Answers to some questions about stainless steel cylinder:

Does the excavator use a hydraulic cylinder?
First, construction machinery is generally a hydraulic cylinder. Second, hydraulic transmission equipment is usually composed of four components, power, execution, control and auxiliary. And the hydraulic cylinder as a linear reciprocating motion or less than 360. Reciprocating motion of the hydraulic mechanism, simple structure, reliable work, is also widely used in the hydraulic system of the main actuator, it is the prime mover in the form of mechanical energy to drive the hydraulic pump produced by the liquid pressure energy, and then can be directly driven load for reciprocating movement or less than 360.

What is the main maintenance of the cylinder?
After disassembling the cylinder: 1, clean the cylinder and piston; 2, replace all seals; 3, if there is a valve to repair, to ensure sealing and flexible; 4, deal with all deformation parts; 5. Installation experiment.