This article mainly introduces:

Turkey hydraulic cylinder,100 ton hydraulic cylinder manufacturer,100 ton hydraulic cylinder

(Turkey 100 ton hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

100 ton hydraulic cylinder are widely used in Turkey，because of excellent fatigue and impact resistance，no need for deceleration device，high work efficiency.So our company has designed 100 ton hydraulic cylinder for customers from Turkey.

Introduction to 100 ton hydraulic cylinder:

At the rated pressure, the thrust of the 100 ton hydraulic cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the 100 ton hydraulic cylinder is related to the diameter of the 100 ton hydraulic cylinder, but not to the stroke of the 100 ton hydraulic cylinder. Moreover, the larger the 100 ton hydraulic cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the 100 ton hydraulic cylinder.

The main role of the 100 ton hydraulic cylinder: the 100 ton hydraulic cylinder is an executive element in the hydraulic transmission system, which is an energy conversion device that converts hydraulic energy into mechanical energy. The hydraulic motor realizes continuous rotary motion, while the 100 ton hydraulic cylinder realizes reciprocating motion. The structure of the 100 ton hydraulic cylinder has three categories: piston 100 ton hydraulic cylinder, plunger 100 ton hydraulic cylinder, swing 100 ton hydraulic cylinder, piston 100 ton hydraulic cylinder and plunger 100 ton hydraulic cylinder to achieve reciprocating linear motion, output speed and thrust, swing 100 ton hydraulic cylinder to achieve reciprocating swing, output angular speed (speed) and torque. In addition to the single use of the 100 ton hydraulic cylinder, two or more can be combined or used in combination with other mechanisms. To fulfill a special function. The 100 ton hydraulic cylinder has simple structure and reliable operation, and has been widely used in the hydraulic system of machine tools.

100 ton hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching 100 ton hydraulic cylinder block - fine boring 100 ton hydraulic cylinder block - grinding 100 ton hydraulic cylinder block. The rolling method is: broaching 100 ton hydraulic cylinder block - fine boring 100 ton hydraulic cylinder block - rolling 100 ton hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the 100 ton hydraulic cylinder block is about 1-2 days, rolling 1 meter of the 100 ton hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the 100 ton hydraulic cylinder increases by 25%. If the 100 ton hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality 100 ton hydraulic cylinders, you must take the rolling production process. After the 100 ton hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

If the piston rod and 100 ton hydraulic cylinder are stuck or the 100 ton hydraulic cylinder is blocked, at this time, no matter how to operate, the 100 ton hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the 100 ton hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about 100 ton hydraulic cylinder:

What is the cause of the sound of the excavator arm cylinder?
Hydraulic excavator cylinder includes boom cylinder, bucket rod cylinder and bucket cylinder, four cylinders. The sound of boom cylinder may be the wear of hydraulic cylinder block bushing, piston rod bushing and shaft pin. The main reason: poor lubrication, followed by improper clearance in the assembly process. Countermeasures: (1) Strictly lubricate each shaft pin at least once every 8 hours when the excavator is initially used for 100 hours and under harsh conditions; In other working conditions, lubricate each pin at least once every 50 hours. (2) If the lubricating oil passage is found to be blocked, it must be stopped for rectification. (3) Require assembly, replacement of all parts of the shaft pin, bushing strictly comply with the assembly testing standards and operating procedures.

CNC lathe rotary cylinder oil leakage and treatment methods
Oil leakage often occurs when the cylinder (especially the hollow cylinder) of the CNC lathe is installed. First check the cylinder yaw, be sure to reach or close to the required value, generally the cylinder requires the outer beat within 1 wire. Otherwise, too much beating is sure to leak oil. Then check whether the tubing is smoothly downward at a certain Angle, and can not bend. Look at the pipe outlet can not go into the oil level, to a little higher. Otherwise, there's back pressure and it's gonna leak.